1. Home
  2. Navien
  3. tankless water heaters
  4. Code E003

Navien tankless water heater code E003: Ignition failure

Tankless water heater, Canada and United States

The heater tried to light the burner and it did not light.

This needs a licensed gas technician. There are a few safe checks you can do first, marked below. Anything inside the unit is a job for a professional.

This involves the gas supply or burner. Only a licensed technician should open the unit or work on gas parts.

What causes it

Canadian and US models

  1. The main gas supply valve to the heater is closed, or the gas supply is off.

    Check the gas supply is onYou can do this

    1. Check whether your other gas appliances, such as the cooktop, are working.
    2. Check the gas isolation valve to the unit is open. On most quarter-turn valves the handle sits in line with the pipe when open.
    3. On bottled LPG, check the cylinder is not empty and the cylinder valve is open.
      If you smell gas, do not use switches or flames. Leave the area and call your gas emergency line.

    Clear a Navien error codeYou can do this

    1. Deal with the cause first, using the checks listed for the code.
    2. On NPE-A2 and NPE-S2 models, press the Back button on the front panel. On first-generation NPE-A and NPE-S models and on indoor NPN models, press the Reset button on the front panel.
    3. If an NR-21DU remote controller is fitted, you can press its OK button once instead. On outdoor NPN models, which have no front panel, the remote is the way to reset. The remote shows RST when the error is reset.
    4. If the code comes back, stop resetting. Note the code and the model number and contact Navien technical support or a licensed technician.
      Resetting over and over can hide a fault that needs a technician.

  2. A fault in the gas or ignition system that needs a technician. Suspect this when the code comes back with the gas supply on.

    Book a licensed gas technician

US models

  1. The main gas supply valve to the heater is closed, or the gas supply is off.

    Same check as above: Check the gas supply is on

    Same check as above: Clear a Navien error code

  2. The heater's gas manifold or its gas type DIP switch setting does not match the type of gas supplied.

    Book a licensed gas technician

  3. A fault in the gas or ignition system that needs a technician. Suspect this when the code comes back with the gas supply on.

    Book a licensed gas technician

How to read this code on your unit

Booking a licensed gas technician

Contact Navien before booking a repairYou can do this

  1. Have the model number, serial number, purchase date, where the heater is installed and the error code ready.
  2. Call Navien Technical Support on 1-800-519-8794, or contact the company that installed the heater.
  3. For a repair under warranty, the installer or service provider must contact Navien before starting the work.

Book a licensed gas technicianlicensed gas technician

  1. Turn the unit off and leave the covers on. Gas components must only be serviced by a licensed technician.
  2. Note the code, how often it appears, and the model and serial numbers from the rating label.
  3. Book a licensed gas technician and give them those details.

Models that show this code

21 models in 6 ranges
RangeModels
NPE-A (first generation)NPE-180A, NPE-210A, NPE-240A
NPE-S (first generation)NPE-150S, NPE-180S, NPE-210S, NPE-240S
NPE-A2NPE-180A2, NPE-210A2, NPE-240A2
NPE-S2NPE-180S2, NPE-210S2, NPE-240S2, NPE-150S2
NPN-ENPN-120E, NPN-160E, NPN-180E, NPN-199E
NPN-UNPN-160U, NPN-180U, NPN-199U

Where this comes from

Checked against the manufacturer's manual on 9 October 2026.

Report a mistake on this page

Other Navien tankless water heater codes

Code Meaning What you can do
E004 False flame detected Safe checks first, then a pro
E012 Flame lost Safe checks first, then a pro
E016 Heat exchanger overheated Safe checks first, then a pro
E030 Exhaust too hot Safe checks first, then a pro
E031 Burner overheated Call a pro
E046 Limit control fault Call a pro
E047 Exhaust temperature sensor fault Call a pro
E056 Modulating gas valve fault Call a pro
E060 Dual venturi fault Call a pro
E109 Fan motor fault Safe checks first, then a pro
E110 Abnormal air pressure (blocked vent or intake filter) Safe checks first, then a pro
E127 Air volume sensor fault Call a pro

See all ignition failure codes on tankless water heaters across brands.